Place of Origin:
ShenZhen China
Brand Name:
changdaneng
Certification:
CE
Model Number:
CDN-BO01
Contact Us
Half moon 6 pcs led light cast aluminum solar warning lights on both sides of the road
SPECIFICATIONS
Dimensions 125*43*30mm
Weight 330g
Housing material Solar cell&I.C(integrated circuit)
Covered with U.V coated polycabonate(super-intensity)
Out case Aluminum alloy
Reflector Corner cube,Lexan 143
Refector color Yellow / Red / White / Blue / Green
LED 3 pcs per side
LED color Yellow / Red / White / Blue / Green
LED output 5000 mcd
LED output frequency Steady or flashing
LED visibility Up to 1000 meters
Activation Photo sensor
Storage device Super capacitor or NI-MH battery
Capacitor cavity 800mAh
Charge condition Sunny day -2hr,/Rainy day-8hr.
Life span Up to 5 years for NI-MH battery type
Lighting time 12-16 hour for steady model after charged fully
Waterproof IP68
Operating temperature -25 to +80C
Manufacturer’s warranty One year
FEATURES
Solar powered high intensity LEDs for superior performance in luminosity.
Super strong polycarbonate cover and aluminium shell for impact durability.
Maintenance free design. Automatic on/off light sensor activation.
Simple installation. Same procedure as with existing conventional markers.
Stud-free mounting for off-ground installation, eg. guard rails and barriers.
Operational life time is 3 to 5 times longer than conventional markers.
Double sided, single sided, 5 colours, steady or flashing modes.
Solar road stud is easy to install with virtually no maintenance.
APPLICATIONS
Solar powered markers, bricks and other products can and should be used for:
Wet Roads,Foggy Conditions,Dark Rural Country Roads
Dangerous blind corners and sharp-curves, black spots and poorly lit areas...
Areas with whimsical and unpredictable weather conditions (coastal roads, foggy areas, wet and rainy regions, etc.)...
Joint intersections, on and off ramps, center lines and dividers, entrance warnings, carpool lanes, bridges, crosswalks...
Guidance lines, traffic islands, roundabouts, aprons, mountain roads...
Taxiways at airports, bike and pedestrian lanes, aboard ships and watercrafts...
Entertainment areas, parking lots, hotel entrances, gas stations and many more!
INSTRALLATION
The Solar road stud Series accumulates energy and charges itself throughout the day. As soon as dusk begins to fall, the L.E.D.s start working automatically. The solar road studs are developed to ensure a higher degree of safety for cars and drivers at blind spots and dangerous hard-to-see areas on the road.
For optimal performance, the recommended distance between each solar road studs are as follows:
| Install Site | Distance |
| Highways and Expressways | 7 - 8 yards (5 - 6 meters) |
| Dangerous Entrances and Exits | 4 - 5 yards (2 - 3 meters) |
| Access or Exit ways for Hospitals, Parking Lots, etc. | 0.5 - 3 yards (0.5 - 2 meters) |
Step 1 - Mark the installation points (figure A). See chart above for recommended distances. Areas in tunnels, inside buildings, under bridges, or places where there is no sunlight are not suitable for installation.
Step 2 - Drill the holes using the following specifications (figure B):
Diameter: 1.5" (30-32mm) Depth: 2.6" (60-65mm)
Step 3 - Clean the drilled holes and remove all dirt, sand, dust and moisture. Make sure the hole is dry before applying any adhesive (figure C). Also prior to using adhesive, place the SolarMarker in the drilled hole and check for a tight and even fit as well as clearance for the desired alignment.
Step 4 - Fill up the drilled hole with hot melted glue or regular epoxy (figure A) and place the SolarMarker into the adhesive paste. Align accordingly (figure E).
Step 5 - Check and make sure that the glue is completely dry and settled before exposing the solar road studs to traffic and road activity. Check the manufacturers' recommendations for proper drying time for the adhesive.
packing:
Send your inquiry directly to us
